Wolverine Stack Dosage & Reconstitution Guide
Research and educational use only — not medical advice, and not for human consumption. The figures below are summarized from public sources, product labeling, and community reports, and are not a prescription or a substitute for a qualified clinician.
Reconstitution
Wolverine Stack ships as a freeze-dried (lyophilized) powder that has to be mixed with bacteriostatic water before use. Draw 2 mL of bacteriostatic water into a syringe and add it to a 10 mg vial, letting the stream run down the inside wall of the glass rather than blasting the powder directly. Swirl gently — never shake — until the solution is clear, then keep it refrigerated.
Worked example. 2 mL into a 10 mg vial gives a concentration of 5 mg/mL (5000 mcg/mL). A 2 mg dose then works out to 0.4 mL = 40 units on a U-100 insulin syringe. Scale the water volume up or down to make your target dose land on an easy-to-read mark (1 unit = 0.01 mL).
- Wipe both vial stoppers (peptide and bacteriostatic water) with an alcohol swab and let them dry.
- Draw 2 mL of bacteriostatic water into a syringe.
- Inject it slowly against the inside wall of the peptide vial.
- Swirl gently until fully dissolved; do not shake.
- Label the vial with the contents, concentration, and date, and store it in the refrigerator.
Dosing schedule
| Phase | Dose | Volume | Insulin units (U-100) | Notes |
|---|---|---|---|---|
| Week 1 | 0.5 mg | 0.1 mL | 10 units | daily — ≈250 mcg of each compound |
| Weeks 2+ | 1 mg | 0.2 mL | 20 units | daily — ≈500 mcg of each |
| Upper range | 2 mg | 0.4 mL | 40 units | daily — ≈1 mg of each |
Timing & cycling
Blended BPC-157 + TB-500 vial. Any consistent daily time; near the injury if convenient.
Cycle length. 4–8 weeks per healing block.
Storage & handling
Keep the lyophilized (unmixed) vial refrigerated at 2–8 °C (36–46 °F) in a dry, dark place — it tolerates short periods at room temperature during shipping. Once reconstituted, store it at 2–8 °C, never frozen, and use it within about 2–4 weeks (sooner if the solution turns cloudy or discolored). Swab the stopper before every draw and use a fresh needle each time.
Supplies you'll need
- Wolverine Stack vials — about 23 for an 8-week run at the upper dose
- Bacteriostatic water — 2 mL per vial (a 10–30 mL multi-dose bottle covers several vials)
- U-100 insulin syringes (0.3–0.5 mL / 30–50 unit barrels are easiest to read) — roughly 112 for 8 weeks, plus spares
- Alcohol swabs — one per injection and one per vial draw
- Sharps container for safe needle disposal
Key points
- Serum Research's Wolverine Blend vial is 10 mg total = 5 mg BPC-157 + 5 mg TB-500 (1:1). Doses above are TOTAL blend volume; each 1 mg of blend delivers ≈500 mcg of each peptide.
- Confirm the BPC:TB ratio on your COA and recalculate if it isn't 1:1.
- Dosing each peptide separately (see their pages) gives finer control than a fixed blend.
What to monitor
Track the injury itself — pain, range of motion, load tolerance.
Legal & prescription status
No legal prescription exists. It is an unapproved research chemical, sold only for laboratory research and labelled 'not for human consumption.' It is not FDA-approved for any human use.
References
This guide is for research and educational purposes only. It is not medical advice and does not describe a product approved for human use. Always consult a qualified healthcare professional before considering any peptide protocol.